.. _bareboxdt: Barebox devicetree handling and bindings ======================================== The preferred way of adding board support to barebox is to have devices on non-enumerable buses probed from device tree. barebox provide both the Linux OpenFirmware ``of_*`` and the libfdt ``fdt_`` APIs for device tree parsing. The former makes porting the device tree specific bits from Linux device drivers very straight forward, while the latter can be used for very early (PBL) handling of flattened device trees, should this be necessary. Additionally, barebox has support for programmatically fixing up device trees it passes to the kernel, either directly via ``of_register_fixup`` or via device tree overlays. Upstream Device Trees --------------------- barebox regularly synchronizes with the Linux kernel device tree definitions via the `kernel.org Split device-tree repository`_. They are located under the top-level ``dts/`` directory. Patches against ``dts/`` and its subdirectories are not accepted upstream. .. _kernel.org Split device-tree repository: https://git.kernel.org/pub/scm/linux/kernel/git/devicetree/devicetree-rebasing.git/ barebox Device Trees -------------------- For supporting architectures, barebox device trees are located in ``arch/$ARCH/dts``. Usually the barebox ``board.dts`` imports the upstream device tree under ``dts/src/$ARCH`` with ``#include "$ARCH/board.dts"`` and then extends it with barebox-specifics like :ref:`barebox,state`, environment or boot-time device configuration. Device Tree probing largely happens via compatible properties with no special meaning to the node names themselves. It's thus paramount that any device tree nodes extended in the barebox device tree are referenced by label (e.g. ``<&phandle>``, not by path, to avoid run-time breakage like this:: # Upstream dts/src/$ARCH/board.dts / { leds { led-red { /* formerly named red when the barebox DTS was written */ /* ... */ }; }; }; # barebox arch/$ARCH/dts/board.dts #include <$ARCH/board.dts> / { leds { red { barebox,default-trigger = "heartbeat"; }; }; }; In the previous example, a device tree sync with upstream resulted in a regression as the former override became a new node with a single property without effect. The preferred way around this is to use labels directly:: # Upstream dts/src/$ARCH/board.dts / { leds { status_led: red { }; }; }; # barebox arch/$ARCH/dts/board.dts #include <$ARCH/board.dts> &status_led { barebox,default-trigger = "heartbeat"; }; If there's no label defined upstream for the node, but for a parent, a new label can be constructed from that label and a relative path:: # Upstream dts/src/$ARCH/board.dts / { led_controller: leds { red { }; }; }; # barebox arch/$ARCH/dts/board.dts #include <$ARCH/board.dts> &{led_controller/red} { barebox,default-trigger = "heartbeat"; }; As last resort, the full path shall be used:: &{/leds/red} { barebox,default-trigger = "heartbeat"; }; Any of these three approaches would lead to a compile error should the ``/leds/red`` path be renamed or removed. This also applies to uses of ``/delete-node/``. Only exception to this rule are well-known node names that are specified by the `specification`_ to be parsed by name. These are: ``chosen``, ``aliases`` and ``cpus``, but **not** ``memory``. .. _specification: https://www.devicetree.org/specifications/ Device Tree Compiler -------------------- barebox makes use of the ``dtc`` and ``fdtget`` and the underlying ``libfdt`` from the `Device-Tree Compiler`_ project. .. _Device-Tree Compiler: https://git.kernel.org/pub/scm/utils/dtc/dtc.git These utilities are built as part of the barebox build process. Additionally, libfdt is compiled once more as part of the ``CONFIG_BOARD_ARM_GENERIC_DT`` if selected. Steps to update ``scripts/dtc``: * Place a ``git-checkout`` of the upstream ``dtc`` directory in the parent directory of your barebox ``git-checkout``. * Run ``scripts/dtc/update-dtc-source.sh`` from the top-level barebox directory. * Wait till ``dtc`` build, test, install and commit conclude. * Compile-test with ``CONFIG_BOARD_ARM_GENERIC_DT=y``. * If ``scripts/dtc/Makefile`` or barebox include file changes are necessary, apply them manually in a commit preceding the ``dtc`` update. barebox-specific Bindings ------------------------- Contents: .. toctree:: :glob: :maxdepth: 1 bindings/barebox/* bindings/firmware/* bindings/leds/* bindings/misc/* bindings/mtd/* bindings/power/* bindings/regulator/* bindings/rtc/* bindings/watchdog/* Automatic Boot Argument Fixups to the Devicetree ------------------------------------------------ barebox automatically fixes up some boot and system information in the device tree. In the device tree root, barebox fixes up * serial-number (if available) * machine compatible (if overridden) In the ``chosen``-node, barebox fixes up * barebox-version * reset-source * reset-source-instance (if available) * reset-source-device (node-path, only if available) * bootsource * boot-hartid (only on RISC-V) These values can be read from the booted linux system in ``/proc/device-tree/`` or ``/sys/firmware/devicetree/base``.