4. Board support

• 4.1. Aarch64 Qemu virt
  • 4.1.1. Running barebox on QEMU aarch64 virt machine
• 4.2. Texas Instruments AM335x
  • 4.2.1. Building barebox
  • 4.2.2. Starting and updating barebox
  • 4.2.3. AM335x Boards
• 4.3. QEMU vexpress
  • 4.3.1. ARM Qemu vexpress
• 4.4. Microchip (Atmel) AT91
  • 4.4.1. AT91 boards
  • 4.4.2. TODO
• 4.5. Broadcom BCM283x
  • 4.5.1. Raspberry Pi
• 4.6. Cirrus Logic edb9xxx
  • 4.6.1. Cirrus Logic EP9301
  • 4.6.2. Cirrus Logic EDB9302
  • 4.6.3. Cirrus Logic EDB9302A
  • 4.6.4. Cirrus Logic EDB9307
  • 4.6.5. Cirrus Logic EDB9307A
  • 4.6.6. Cirrus Logic EDB9312
  • 4.6.7. Cirrus Logic EDB9315
  • 4.6.8. Cirrus Logic EDB9315A
• 4.7. TI Davinci
  • 4.7.1. virt2real
• 4.8. Canon DIGIC
  • 4.8.1. Canon PowerShot A1100 IS
• 4.9. barebox on (U)EFI
  • 4.9.1. Building barebox for EFI
  • 4.9.2. Running barebox on EFI systems
  • 4.9.3. Loading EFI applications
  • 4.9.4. Simple Network Protocol (SNP)
  • 4.9.5. EFI File IO Interface
  • 4.9.6. Block IO Protocol
  • 4.9.7. EFI device paths
  • 4.9.8. EFI variables
  • 4.9.9. EFI driver model and barebox
  • 4.9.10. Building EDK2
  • 4.9.11. (U)EFI Watchdog
• 4.10. Emulated targets
  • 4.10.1. Generic DT image
  • 4.10.2. test/emulate.pl
• 4.11. Garz & Fricke based boards
  • 4.11.1. Santaro (i.MX6)
• 4.12. iBASE MI991AF
  • 4.12.1. Running barebox
  • 4.12.2. Links
• 4.13. Freescale i.MX
  • 4.13.1. Internal Boot Mode
  • 4.13.2. External Boot Mode
  • 4.13.3. i.MX boards
• 4.14. Texas Instruments K3
  • 4.14.1. Building barebox
  • 4.14.2. Running barebox
• 4.15. KVX
  • 4.15.1. KVX boards
  • 4.15.2. Getting a toolchain
  • 4.15.3. Building barebox
  • 4.15.4. Booting barebox
• 4.16. NXP Layerscape
  • 4.16.1. Booting barebox
  • 4.16.2. Flashing barebox
  • 4.16.3. Firmware Blobs
  • 4.16.4. Layerscape boards
• 4.17. MIPS
  • 4.17.1. D-Link DIR-320
  • 4.17.2. MIPS Creator CI20
  • 4.17.3. Loongson LS1B
  • 4.17.4. OKUD MAX9331
  • 4.17.5. QEMU Malta
  • 4.17.6. Ritmix RZX-50
  • 4.17.7. TP-LINK MR3020
• 4.18. Marvell Embedded Business Unit (mvebu)
  • 4.18.1. Move of the Register Window
  • 4.18.2. RAM initialisation
  • 4.18.3. Booting second stage
  • 4.18.4. Booting from UART
  • 4.18.5. mvebu boards
• 4.19. Freescale MXS
  • 4.19.1. Bootlets
  • 4.19.2. Booting Freescale i.MXs
  • 4.19.3. Booting from USB
  • 4.19.4. Booting from SD cards
  • 4.19.5. Booting second stage
  • 4.19.6. MXS boards
• 4.20. Texas Instruments OMAP
  • 4.20.1. Bootstrapping a PandaBoard
  • 4.20.2. Networking
• 4.21. OpenRISC
  • 4.21.1. Optaining an OpenRISC toolchain
  • 4.21.2. Running OpenRISC barebox on qemu
  • 4.21.3. or1ksim
• 4.22. PowerPC boards
  • 4.22.1. Phytec phyCORE-MPC5200-Tiny
• 4.23. PXA boards
  • 4.23.1. Phytec phyCORE-PXA270
• 4.24. RISC-V
  • 4.24.1. QEMU Virt
  • 4.24.2. TinyEMU
  • 4.24.3. BeagleV
  • 4.24.4. Erizo
  • 4.24.5. Allwinner D1 Nezha
• 4.25. Rockchip RK3288
  • 4.25.1. Building barebox
  • 4.25.2. Starting and updating barebox
  • 4.25.3. RK3288 Boards
• 4.26. Rockchip RK3188
  • 4.26.1. Radxa Rock
• 4.27. Rockchip RK356x
  • 4.27.1. Supported Boards
  • 4.27.2. Building
  • 4.27.3. Creating a bootable SD card
  • 4.27.4. USB bootstrapping
• 4.28. Sandbox
  • 4.28.1. Building barebox for simulation
  • 4.28.2. Running the sandbox
• 4.29. Altera SoCFPGA
  • 4.29.1. Bootstrapping
  • 4.29.2. Updating handoff files
  • 4.29.3. Integrating new SDRAM driver
• 4.30. STMicroelectronics STM32MP
  • 4.30.1. Building barebox
  • 4.30.2. Flashing barebox (FIP)
  • 4.30.3. Flashing barebox (legacy stm32image)
  • 4.30.4. USB Bootstrap (DFU)
  • 4.30.5. Boot source selection
  • 4.30.6. Boot status indicator
• 4.31. Nvidia Tegra
  • 4.31.1. Building
  • 4.31.2. Kickstarting a board using USB
  • 4.31.3. Writing barebox to the primary boot device
• 4.32. UEMD
  • 4.32.1. MB 77.07
• 4.33. Xilinx ZynqMP Ultrascale+
  • 4.33.1. Image creation
  • 4.33.2. Booting Barebox